The T Shirt is 100% cotton pre shrunk Gildan 5000 shirt. 1 Middle Weight Contender; Comfy Men’s Short Sleeve Blank Tee Shirt. 100% Cotton. Strong double needle stitched neckline and bottom hem. Shoulder-to-shoulder taping. Quarter turned. Seamless collar The Digital Printed Transfer and will be placed centered on the t shirt If there are any questions are you need any help with the design please feel free to contact us we will try our best to answer message very quickly and we would love to hear from you. If you would like bulk pricing on any of our products please let us know and we can give you special bulk pricing.
Click here to buy this shirt: Geelong Cats Afl Grand Final Champions 2022 Mug, hoodie, tank top and long sleeve tee
Steam setting can be done by saturated or super heated steam. During steaming, uniform treatment can be ensured by initial sequence of alternate short steaming and vacuum application for 20 – 30 min at 130°C under pressure. Super heated steam can be used in stenters and setting time is 25% shorter than for hot air on account of quicker heating up rate. Acrylic fibres have to be protested as some may undergo excessive shrinkage or loss of handle. Before the material is heat set, it should be thoroughly washed to remove spin preparations, lubricants, sizing agents and impurities as these are likely to be burned in drying heat setting making their removal difficult. Steaming at temperatures above 100°C (generally 120°C or 130°C) also reduces the pilling tendency as a result of increasing the coefficient of friction.
Fuzz formation is result of constant gentle abrasion. In a garment, it is usually observed near the abrasion areas such as near the pocket, collar, etc. The pilling tendency of fabrics depends on denier of fibres, twist factor of yarn, construction of fabric and processing steps used during the manufacture of fabric as under: 1. Denier of fibres: Fine denier fibres tend to pill more as they possess less stiffness. Secondly, fibres per unit length of yarn will be more in a case of fine denier compared to the yarn made from coarser denier so that there will be more fibre ends exposed rendering the fabric more prone to pilling. 2. Twist factor of yarn: The yarn with lower twist factor below 3.4 will pill more than the yarn with higher twist factor. It is therefore necessary to choose slightly higher twist factor for single /doubled yarn if it would not adversely affect the feel of the fabric. The double yarn exhibits less pills.
The different chemical finishing approaches have been made to prevent pill from accumulating on fabric surface which include the following: b) Application of enzymes (bio-finish) to 100% cotton textiles to cause removal of loose fibres in the yarn to reduce pilling tendency. The polymeric formulations bring about the binding of the loose fibres into the fabric. The products normally used in this type of finish are friction-reducing lubricants to minimize damage due to abrasion. The acrylic co-polymers, which can be modified to suit the requirements are normally used. Examples of few are: b) Application of enzymes (bio finish) to 100% cotton textiles to cause removal of loose fibres in the yarn to reduce pilling tendency In the second approach, biopolishing with cellulase enzyme is carried on 100% cellulosic or cellulose rich blend fabrics to eliminate loose fibres, which results in clean and smooth surface with improved pill rating. The bio-polishing process targets the removal of the small fibre ends protruding from the yarn surface and thereby reduces the hairiness or fuzz of the fabrics. The hydrolysis action of the enzyme weakens the protruding fibres to the extent that a small physical abrasion force is sufficient to break and remove them. Biopolishing can be accomplished at any time during wet processing but is most convenient performed after bleaching. It can be done in both continuous or batch processes. However, continuous processes require some incubation time for enzymatic degradation to take place. Removing the fuzz makes the colour brighter, the fabric texture more obvious, and reduces pilling.
Suitable for Women/Men/Girl/Boy, Fashion 3D digital print drawstring hoodies, long sleeve with big pocket front. It’s a good gift for birthday/Christmas and so on, The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness, The print on the item might be slightly different from pictures for different batch productions, There may be 1-2 cm deviation in different sizes, locations, and stretch of fabrics. Size chart is for reference only, there may be a little difference with what you get.
- Material Type: 35% Cotton – 65% Polyester
- Soft material feels great on your skin and very light
- Features pronounced sleeve cuffs, prominent waistband hem and kangaroo pocket fringes
- Taped neck and shoulders for comfort and style
- Print: Dye-sublimation printing, colors won’t fade or peel
- Wash Care: Recommendation Wash it by hand in below 30-degree water, hang to dry in shade, prohibit bleaching, Low Iron if Necessary
This product belong to huynang